Menu Close

Amp hook up to radio, how to install a car amp (with pictures) - wikihow

Warnings Be careful when around the electrical system of your car. You will need to connect a radio receiver to its input one way to do this is to build the receiver yourself as described in the Expert Answer above. Ft is one sexy looking rig. How do I feed my speaker through the door with the door wire harness in the way? Run your power, ground, and remote wires.

Amp hook up to radio

Need help hooking up antenna tuner radio and amplifier - ARCOM

Use a capacitor to prevent voltage drops caused by deep bass hits, i. Put inputs left and right in the correct slots. You must wire the remote wire from the amp to and ignition source of power a component which turns on when the ignition in the car is engaged. Make sure the car is completely turned off to avoid electrical shock or injury. Share your experience with Bill Crutchfield.

If they are, then hook up an external speaker to the radio's output for that side to see if it is the radio at fault. The speaker wires coming from the amplifier's outputs hook up to your vehicle's harness connected to the car speakers. Then hook the sub which should be in an enclosure to the amp. Another popular way to connect an amplifier to a factory radio is to use something called a line output converter.

How to Wire an Amp to a Sub and Head Unit 12 Steps

How to Wire an Amp to a Sub and Head Unit 12 Steps

Yea I think I got it now say forward is into receiver and back means out. Using factory speaker wiring for a watt amp should be okay. To do that is it something as simple as just unplugging the wire from the old speakers and plugging them into the new ones? Run your rca from amp to the line converter.

Connect the end coming from the radio plug to a new wire going to the amp's input. To submit your questions or ideas, or to simply learn more about It Still Works, contact us. Now that your amp is tapped into your car's factory audio system, run speaker wires from the amp's speaker outputs to the speaker s or sub-woofer s you want the amp to power. View Quote View All Quotes. Hi, I recently put a new stereo head into my Hona Civic Cx, soldering the head unit wires into the original system wires and leaving it at that.

Just be sure to tape off any exposed conductors so they can't short by touching anything metal. But amplifiers of watts or less aren't really affected by this. This tutorial will focus on how to add an amp by using speaker-level inputs to tap into your car's existing wiring.

The wires are not grounded properly, check to make sure the surface is clean, unpainted metal. It will produce sound for a second then protect. We'll call you back when it's your turn to talk with the next available. Or would this damage the receiver or speakers? Ive been finding mixed responses on the web.

How to Wire an Amp & Subwoofers Into a Stock Stereo

Amp hook up to radio

You'll get a better idea of what's involved and what solutions are available by talking with an Advisor. If you no longer wish to receive the call, please click the button to cancel your request. Take that fuse out, wrap the remote wire around it, and connect it back where it was. Their toll-free number is on your invoice. Always be careful with electricity.

How to Install a Car Amp (with Pictures) - wikiHow

Consult the owner's manual or the manufacturer of your amplifier to determine the size fuse you should use. Which by the way the speakers are a joke. In other words, do not mount it on a metal surface. Yes, this is very possible. Instructions from both manuals are confusing.

Video of the Day

It has only four speakers. Once you've identified each of the eight speaker wires, cut each one. How do you put an amp and subwoofer in an Chevrolet pickup? If you've ever heard an electric guitar in maximum overdrive mode, dating you have a sense of what will happen. Warnings Always Disconnect the Negative terminal from your battery before doing anything with electricity on your car.

Joseph, It depends on your specific vehicle. Connect the remote wire to the remote wire ran to my existing amp back there already. Get your capacitor as close to the amp as possible, and use the same ground as you did for the amp.

How do you hook up amp to a radio with no RCA input

Just connect two speakers, left dash and door speakers, for example, to each amplifier output terminal. Put a rubber grommet in the hole to keep the wire from chaffing. David, Check out How to connect an amp to a factory stereo for help with what you want to do. Montana, In the wiring system described in this article, no new wires are run to speakers.

How to Add an Amplifier to a Factory Stereo

Connect the speaker wires from the amplifier to the speakers. This converter can then be connected directly to your amplifier's line level inputs. Rate your experience with us. Warnings Never drill inside a car's parts unless you know exactly where the drill bit is going.

No wiring harness available yet. Your article was very clear and I appreciate your help. Okay, so after running front and rear speaker outputs from the head unit to amp's speaker input terminals, what do I do about the amp's sub input since I have no outputs from the head unit? Items you will need Amplifier with speaker-level inputs Amp installation kit gauge speaker wire Electrical tape Wire stripper Socket set or adjustable wrench Screwdriver. You'll need one for the amp's input and the other for its output.

It Still Works

How about if I wanna have component speakers of the front and coaxial on the back? Caleb, If you bought your gear at Crutchfield, modern songs to hook you could call Tech Support for free help troubleshooting your system. Can you run a car amp output into another car amp? Jorge ochoa from Santa Ana ca.

How do you hook up amp to a radio with no RCA input
  1. Can I also run my door speakers all on this one amp using the output wire harness coming off the the amp and other for sub?
  2. The other ends of these wires connect to the vehicle's harness.
  3. Each amp manufacturer does it differently - some use interconnecting cables, some use switches.

How to Connect an Amplifier to a Factory Stereo

  • How would what I am looking to do be spliced in?
  • With a line output converter.
  • Now attach a line of speaker wire to each splice and secure with electrical tape.
  • Is this because of the wiring difference?
  • To really highlight the bass of your car stereo, you need a setup capable of properly reproducing low frequency notes.

Another strategy would be to use a vehicle-specific amp replacement module and harness to install a new amplifier in your Grand Cherokee. Wear hearing protection when adjusting the amp's settings. They can cause noticeable power loss when higher wattages try to get through.

Amp hook up to radio
Buck Pomerantz

Get real help from an expert like Enrique Contact us. So if you're upgrading a complex system, using a line output converter might be your best option. Pete, I don't see why not.

Connecting Your Car Speakers to an Amp Use Your Factory Wiring

  • Melbourne city dating
  • Dating the fossil record answer key
  • Daisy chain hook up
  • Army dating sites australia
  • Dating websites for police officers
  • How do you hook up atari 2600