Menu Close

Amp hookup, the rv hookups to know before your first trip

  1. Take that fuse out, wrap the remote wire around it, and connect it back where it was.
  2. Now you'll want to set your gains properly.
  3. Most importantly, make sure the polarity is the same for all speaker connections.
  4. Similarly, the speaker outputs on most amps and the inputs on most speakers are color-coded red and black.
  5. It's not there to protect your audio equipment, it's there to protect your car.
  6. It is a very important wire and your amplifier will not work without it.

For more help on choosing a fuse size visit this page. When you reach the amplifiers you may need to wear hearing protection to adjust them to their maximum level. Consult the owner's manual or the manufacturer of your amplifier to determine the size fuse you should use. To Separate or Not to Separate? Connect the remote turn-on wire to your amplifier using an appropriate connector such as a ring terminal.

If you have a Dremel type tool with a metal brush these work great wear eye protection. Now I know how to do it and why. If you have any problems after the installation be sure to read over these three articles. If you don't hear distortion even at the loudest setting, the head unit is in good shape. The subwoofer is hooked up to the receiver with a single interconnect cable.

The RV hookups to know before your first trip

However, you will need to connect your speakers to the amp and turn it on. There is also a wiring diagram below. Start from the interior of the car, and make sure the wire won't get pinched or caught on anything.

You can also contact the manufacturer and ask them for that information. Make sure you know how to reactivate your radio before doing this, new if your radio has a security system. Installing car audio amplifiers is one of the trickiest things a newbie car audio installer can attempt.

How to hook up a subwoofer to a stereo system

If it does, then turn your car off and make sure the amp turns off as well so it doesn't drain your battery. Get out the power drill and steel drill bits. Connect the power wire to the battery using appropriate connectors for the wire and battery terminal. Protect the electrical hook-up box with a master disconnect switch and an appropriately-rated circuit breaker installed between it and the power supply.

  • Warnings Never drill inside a car's parts unless you know exactly where the drill bit is going.
  • Subwoofer connection to a two-channel system differs from the methods used in home theaters.
  • Click Here if you don't have a remote wire or are using a factory head unit.
  • Situate these wires away from the power wires.
  • It can be done using an oscilloscope but since few people have one of those laying around we'll cover doing it by ear.

Consult the owner's manual of your amplifier s to find out the maximum current draw of your system. It can be connected to the negative battery side or somewhere metal in the car. If you have a factory deck and install an amp, there's really no wire to connect the amp to on the factory deck. Pull back the carpet in the area you intend to run the power wire. Start with a pilot hole and then work your way up to a size that will fit your wire.

Water Hookups

Most speakers have two terminals of varying sizes. You do not want to run power wires and speaker wires on the same side of the vehicle. Troubleshooting Car Audio Amplifiers. Uni-Bit that would be great to use see photo. Make sure the control wire from your deck to the amp is connected.

Before drilling make sure you know where the bit will end up once it's through the firewall. Repeat this process for the input gain, and then with all the other components. Always consult manufacturer's literature and local codes to ensure your installation is correct. As before, turn up the gain until you hear audible distortion. For multiple items using the remote wire you will want to use a relay.

You've just learned to properly adjust the settings on your car audio system. Wear hearing protection when adjusting the amp's settings. Do not insert the fuse until all other connections are made! With this arrangement, the stereo speakers and sub receive all of the bass, midrange, and treble frequencies. Turn the deck's volume up slowly until you begin to hear distortion.

Connect the speaker wires from the amplifier to the speakers. Turn up the deck's volume until you hear distortion, and set it just below that level. Locate the electrical hook-up box in an area where it will be protected from direct rain and accidental contact, particularly from moving vehicles. Normally, such things are marketing hype, but I see no marketing benefit to this. However, this is generally not recommended, because you lose any noise rejection and ground-loop isolation.

If there is no available hole, use a power drill and steel bits to drill one. Consult the schematic for your deck to be sure which wire this is. Find a spot to run the power wire through the firewall.

It Still Runs

How to Install an RV Home Hookup

Hooking up water to your RV
Report Abuse

See the instructions below. Play some music and verify that everything sounds right. Do not attempt to install an amp if you do not feel comfortable with the procedure.

How to Install an RV Home Hookup

Is this article up to date? Level setting, done by ear, is more art than science. After all connections are in place and all wires are secured, you may insert the main power wire fuse. Protect the drilled hole edges from rust with paint or a similar material. Forcing a volt plug into a volt socket would at best result in a dead short, and at worst in every appliance being burned out and a risk of fire.

The RV hookups to know before your first trip

Hard rock would be a bad choice here. If the radio is good, it could be a bad speaker. Connect the wires just like you would to your speakers. It is best to install it as close as possible to the connection. After you have your power wire run the way you want it, go back and use plastic wire ties to secure the wire in place.

What you could do instead is locate your fuse box and find a fuse that turns on when you turn the key in your car. Items you will need Electrical hook-up box Master disconnect switch Circuit breaker Wire Basic electrical tool kit. You can find this loom at auto parts stores and Parts Express. That's all there is to it. Decide what level of provision the electrical hook-up box must answer.

How to Install a Car Amp (with Pictures) - wikiHow

How to Install a Car Volt Amp Gauge (with Pictures) - wikiHow

Leave it to a professional. If you are installing a car audio capacitor you will need to charge it first. Paint the hole's edges to protect against rust. Now here are the steps on how to install a car amp. Once you have set up your amp, khloe is it's time to kick back and enjoy the sound of your new separates.

Hooking up power to your RV

  • Western dating rules
  • Ex gf dating a loser
  • Senior dating sites pittsburgh
  • Novel dating kontrak 19
  • Speed dating kwejk
  • Online international dating scams
  • Doctor dating australia