After reattaching your pool equipment, sex dating christian you should reinstall your deck equipment. The reopening process begins the moment the pool is closed. Leave a Reply Cancel reply Your email address will not be published.
When you move the handle up and down, you are shaking the old D. Take the supplies chemicals out of storage and replace those that have exceeded the expiration date. After your pool is turned on and circulation begins, you should walk around and inspect all of the various parts for leaks and other possible issues. Opening your pool Every pool owner should learn how to properly open their pool. So if you do not have a bag of D.
Pumps & Filters
If an above ground pool, the excess water may be siphoned off instead. Your current location is outside the Next Day Delivery area. Winter Covers Solid Winter Covers. Stabilized forms of pool chlorine are recommended for normal daily use after the initial clean up of the water. Probably means an underground pipe leak at that point.
- Vacuum any debris out of the bottom.
- Once you have shut the valve on the filter tank you can, once again start the Perflex Filter back up.
- Test and adjust the pH and total alkalinity.
- Backwash the filter thoroughly.
This will prevent you from having to run out to buy replacements later. You are ready to start filtering your pool! You could bleach and stain the liner.
If you do not store your cover indoors, and you keep it outside or in a shed, then you do not have to worry about getting the cover particularly spotlessly clean. This will wash all of the old and dirty, debris and D. If the water level goes down to any other level on the side walls and then stops, this usually means that the leak is in the liner on the pool side wall or possibly in the step unit gasket. Clean off items and fold properly and store away.
Re-install the skimmer baskets and any return jet eyeball fittings. They make a few different sizes of this Perflex pool filter. Treat the water with an algaecide. Make sure you set up a schedule for regular maintenance checks so that you can keep your filter system operating at peak efficiency for many years to come!
Support - Hayward Pool Products
- Skip to the beginning of the images gallery.
- Sand filters require backwashing every few weeks to churn the sand and flush out the trapped dirt.
- If you are loosing water as well, we suggest contacting a local pool professional.
- These o-rings are made from rubber and stop the water from leaking through the bump shaft, From time to time these o-rings will have to be replaced.
- When the tube sheets crack they will allow D.
Pump, hose, or sweep away water, dirt, or debris from the cover and deck. If the water level goes down past they side walls, then it usually means that the leak is in the pool floor. If an above ground pool, wordpress dating templates you may have to re-attach the actual skimmer and return fittings onto the pool depending on how the pool was closed. Now you will want to replace the handle with the new bump handle. It is best to mix the granular shock chlorine in a bucket and then add that mixture into the skimmer while the system is running.
Sometimes things don't go so smoothly after you open your pool. If the chlorine level is high, do not use the pool until it drops to normal levels. If you are looking at buying a pump along with the replacement pool filter, getting the correct size or power of pump is extremely important. What are the specifics I need to know? Re-attach any deck equipment you have such as ladders, rails, diving boards, etc.
Lay out pool cover and sweep or brush off any remaining debris. What is wrong with it and how do I fix it? There is a top tube sheet and a bottom tube sheet. Regardless of your approach, always make sure your pool pump and pool filter including their various parts are secured in place.
The valve will allow you to find the sweet spot, and leave it set there. Reinstall ladders, diving board, and other deck fittings. The pump you want to buy is going to be the same size that you previously had. Every time you back wash your pool filter you are removing the old D. The sooner you work through these steps, the sooner you can host your first pool party this season.
Hayward Perflex D.E Filter Repair & Troubleshooting
Start to slowly peel back your cover, folding it in halves as you do, for easy removal. Houston, we have a problem Sometimes things don't go so smoothly after you open your pool. Check for leaks and proper operation. If anything seems off or your filter doesn't appear to be firing on all cylinders, christian dating sites in shut the pool down and call a pool professional for assistance. Doing so can help you avoid major or even minimal plumbing changes along with having to learn how to maintain a new type of pool filter.
Adjust these chemicals to the proper levels. You will also always want to clean all the parts pf the swimming pool filter as you are working with them. If you see water leaking from your bump shaft on your Perflex filter then you will need to replace your o-rings.
Opening Your Pool
Once the bolt is through you can fully tighten down both bolts and your new handle install will be complete. Start by checking your pH, alkalinity and calcium levels so that you know how to move forward with balancing your pool water. We recommend you wait to shock your pool until the sun starts to go down for it to be most effective. Now that the filter assembly is reconnected to the top of the filter tank you can bolt the top of the filter tank on to the bottom of the filter tank using your bolts or bellyband. Once the bolt is through tighten down the nut clockwise a few turns.
Update Internet Explorer Don't show this message again Close. How do I prepare my Hayward Perflex for it's first use? If the bump handle moves freely like it is not connected to anything, then your filter may need repair. Once you open this valve water will start flowing out. My old one no longer has the model and serial on it.
Hayward Perflex D.E Filter Repair & Troubleshooting
This sand will last years before needing to be replaced. If you covered your pool up properly in the fall you won't have much to vacuum. The tube sheets are pieces of round plastic that have many holes inside of them to hold the filter fingers.
Opening Your Pool
Some dirty water will always manage to get in - don't worry about it. Make sure all of your equipment is ready to get back to work. This in turn helps you save on wasted water and the chemicals used to treat it. Bring the water level up to normal.
You will have to re-use this gasket when you put the filter back together unless you bought a new one when you bought the tube sheets. If an above ground pool, also hookup any hoses from the skimmer and return jets to the pump and filter. Before you can change the valve you will want to backwash your swimming pool filter and then drain it by leaving the backwash valve open until all of the water comes out. Hook up pump, filter and any other additional equipment you might have booster pumps, spa equipment, waterfall circulation pumps, heaters, etc. If you had a backwash hose hooked up to the old valve you can now hook your backwash line on to your new backwash valve.
You see bricks or patio blocks around the skimmers or return jets settling or sinking into the ground. There will be an upper and a lower groove in the shaft for the o-rings to sit into. If you see any small drips or leaks from the new valve, shut off the filter and tighten the valve a bit more. It is always best to replace the c-clips in the perflex when you are changing the tube sheets.